series am1lt-nz 1 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r8.b 1 of 3 north america only features: ? low profile smd (surface mount device) ? operating temperature: -40c to +85c ? 1.5kvdc isolation ? high power density ? pin-out compatible with dcp01 series ? rohs compliant ? short circuit protection models single output model input voltage (v) output voltage (v) output current max (ma) isolation (vdc) efficiency (%) am1lt-0505s-nz 4.5-5.5 5 200 1500 74 am1lt-0509s-nz 4.5-5.5 9 111 1500 78 am1lt-0512s-nz 4.5-5.5 12 83 1500 77 am1lt-0515s-nz 4.5-5.5 15 67 1500 76 am1lt-1205s-nz 10.8-13.2 5 200 1500 73 am1lt-1209s-nz 10.8-13.2 9 111 1500 74 AM1LT-1212S-NZ 10.8-13.2 12 83 1500 76 am1lt-1215s-nz 10.8-13.2 15 67 1500 75 note: all specifications in this datasheet are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. input specifications parameters nominal typical maximum units voltage range 5 12 4.5-5.5 10.8-13.2 vdc isolation specifications parameters conditions typical rated units tested i/o voltage 60 sec 1500 vdc resistance 500vdc 1000 mohm output specifications parameters conditions typical maximum units voltage accuracy see tolerance envelope graph short circuit protection continuous short circuit restart auto-recovery line voltage regulation (single) for vin change of 1% 1.2 % of vin load voltage regulation (single) 10% to 100% load 12.8 % temperature coefficient nominal input,100% full load 0.03 %/ o c ripple & noise 20mhz bandwidth 75 mv p-p minimum load current 10 % of max note: it is not recommended to have the outputs connected in parallel
series am1lt-nz 1 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r8.b 2 of 3 north america only general specifications parameters conditions typical maximum units switching frequency 100% load 100 khz operating temperature -40 to + 85 o c storage temperature -55 to +125 o c maximum case temperature 100 o c cooling free air convection humidity 95 % rh case material epoxy resin(ul94-v0) weight 1.4 g dimensions (l x w x h) 0.77 x 0.42 x 0.20 inches 19.50 x 10.53 x 5.10 mm mtbf >1,500,000 hours (mil-hdbk -217f, ground benign, t=+25 o c) maximum soldering temperature 1.5mm from case for 10 seconds 260 o c pin out specifications pin single 1 +vin 2 -vin 5 -vout 6 +vout 7 nc 8 nc 14 nc nc: not connected dimensions typical characteristics 19.50 (0.77) 10.53 (0.42) 4.50 (0.18) top view side view 5.10 (0.20) 1 7 14 1.00 (0.04) 2.54 (0.10) 6 5 2 8 6.60 (0.28) 1.27 (0.05) 2.54 (0.10) 2.00 (0.08) front view 0.60 (0.02) 7.62 (0.30) 10.53 (0.42) typical load line tolerance envelope graph output current(%) output voltage +2.5% -2.5% -7.5% +10% +5% 10% 50% 100%
series am1lt-nz 1 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r8.b 3 of 3 north america only minimum load requirement in order for this module to operate efficiently and reliably a mi nimum load of no less than 10% of its maximum needs to be maintained at all times during operation. note: this converter should never be operated under no load. if it is required to operate the converter with less than 10% load, it is recommended to install a resistor in parallel with the application load to draw additional current from the convert er?s output to maintain the minimum load condition, or use a converter rated at a lower power. recommended filter circuit if it is required to decrease the input/output ripple, an ?lc? filtering network may be connected to the input and output of th e converter , see above. it should be noted that the inductance and the resonant frequency of the ?lc? filtering network should differ from the dc/dc converter switching frequency to avoid mutual interference. the capacitance of the output filter capa citor must not exceed the values in the table below to avoid startup problems and ensure safe and reliable operation. it is not recommended to connect any exter nal capacitor in the applic ation field when output loading is less than 0.5 watt. external capacitor tables input capacitor (cin) output capacitor (cout) note: 1. datasheets are updated as needed and as such, specifications ar e subject to change without notic e. once printed or downloaded , datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency cert ifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an am bient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary an d may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control sys tems or other such applications which necessitate specific safety and regulatory standards ot her the ones listed in this datasheet. 7. warranty is in accordance with aimtec?s st andard terms of sale available at www.aimtec.com. vout (vdc) cout (uf) 5 10 9 4.7 12 2.2 15 1 vin (vdc) cin (uf) 5 4.7 12 2.2 dc dc + cout +vout - vin single output + vin - vin + cin l l
|
